Tips for using the jumper cables

We all know that using the jumper cables to start the car is a very effective way when your car’s battery suddenly dies. However, what to do to use them effectively and safely is the problem not everyone really knows. In fact, there are some aspects the users must pay attention when making a start by the jumper cables in order to get the success fast with no troubles.

1. The suitable length of the cables

When buying the jumper cables, some people prefer the short cables because of theirs tidiness and convenience. However, the drawback of it is the shortness which can not be used in a long distance. Not every case that the distance between the broken vehicle and the helping one is short but some of them are quite long. Therefore, we must make sure the length of the cables is long enough in the majority of the situation. The suggested minimum length of the jumper cables is about 12 feet. We should buy the cables with this length or even longer.

2. The similar voltage of the batteries

Before you make a jump, you have to make sure that both the batteries have the same voltage. If not, the difference between them can cause the damage to the electrical parts of the batteries.

3. The appropriate distance between two vehicles

For the convenience, you should let two cars as close as possible, but you should never permit two of them to touch each other.

4. The careful and right connection between the two batteries

This is the most important step you must pay a lot of attention when jumping a start.

- Firstly, you attach one of the clamps of the red cable with the positive terminal (+) of the dead battery. You must not let the clamps of the red cables touch the land or the car because it is very dangerous.

- Secondly, you connect the left clamp of the red cable to the positive terminal of the working battery. You do not mind walking many times because it is a good way to limit the fire under any circumstance.

- Next, you attach one of the clamps of the black cable with the negative terminal (-) of the working battery.

- Finally, you connect the left clamp of the black cable with an unpainted metal part of the car. You should not clamp it at the places where there are plastic, paint, and rubber.

If you attach directly this clamp of the black cable with the negative terminal of the dead battery, this can cause the electric sparks combining with the hydrogen, which can cause the fire or explosion.

5. The right disconnection between the two batteries

After your battery is charged and your car can start, you should disconnect the two batteries. But at this time, you should only turn off the helping car and let your car work continuously. You start the disconnection with the black cables which attach with the negative terminal of the batteries. After that, you continue disconnecting between the two positive terminals. You should not let the two clamps of the cables touch each other or let the positive cable touch the vehicle.

6. The recharging for the car

You should keep your car running about 20-30 minutes. At this time, you ought to turn off the lamps, the heater or the other electric equipment so that your battery can be charged faster and more effective.

In conclusion, we should notice that while jumping a start for the dead battery, we must be careful and do right following the directions. To find more tips to using jumper cable, you go to site mygaragestory.net to get more. From that, we can get the safe jump for the car with no differences and troubles.

Top reasons of sump pump’s failure and how to handle them

A sump pump is mechanical equipment which is bound to malfunction for a number of reasons. The reasons for malfunctioning could be its poor manufacturing quality, improper maintenance or due to excessive workload of pumping the water. 

The majority of the sump pump reviews and the helping guides tell us to choose a system which is according to the needs and the product should be of top quality from a top sump pump manufacturer. It should be properly maintained in order to make it work effectively in all kinds of emergency flooding situations in the basement of the house. There are a few common reasons for the failure of sump pump which we will discuss in the next section along with the solutions.

Via: oregonfoundationrepair.com

Top reasons of failure and the solutions:

The following are the main reasons of failure of a sump pump and the associated solutions:
• The power failure – The power failure is one of the most common issues that people face with the sump pumps. The best solution for such an issue is to have a backup electrical power generator which can be manually activated. In case of any mechanical failure, the sump pump wouldn’t be able to initiate itself through a power generator. But, in case of extreme weather conditions which may lead to a power outage, an electric power generator can be a real lifesaver.
• Pump is working but there isn’t any water flowing into the pit – This situation is a classic example of poorly installed equipment. There are many contractors who actually install the system in the sump pump, but they do not hook it up with the drainage system. The proper working of the equipment is dependent on the installation of the drain tile which could be either internally or externally. A clogged, nonexistent or a collapsed drain tile would restrict the flow of water in the pit. So make sure, that this thing is properly installed and is in great working order.

• Jammed switches and the clogged sump pump – The pits of the equipment which are lidless could easily be clogged with debris, pebbles and dirt. Similarly, an equipment installed right beneath a messy sump pit could have its mechanical parts all clogged. If the clogging of the pit interferes with the functionality of the equipment then it may perform slower or could come to a complete halt.
• Improper installation of the equipment – A sump pump must be installed in the exact proper position. An improper installation leads to malfunctioning or it may deteriorate the performance of the system. For this purpose, it is highly advised that the user manual of the product given by the manufacturer must be followed. Further, don’t take it as a DIY task if you are not fully aware about the proper installation. Hiring professionals is always the right thing to do.
• Defects in the product – It is a rare situation, but it is a possibility which could happen. It is advised to always inspect the sump pump for proper functioning after installation and also periodically later on. Chucking a bucket full of water every now and then would tell you about the proper functionality of the equipment.